215-225 (19) Definite Purpose

Subcategory List
-
215-215 (19) Aggregate Duty -- Blue Chip Series -- Crusher -- NEMA Premium -- XRI -- Totally Enclosed -- Three Phase -- High Torque -- (Rigid Base) (16)
Features:
- Meets or exceeds NEMA Premium efficiencies
- Blue Chip Series ® quality, 100% cast iron construction for rigidity and
reduced vibration - 4140 high strength shaft material
- NEMA ® design C, extra high starting and breakdown torque design
- Roller bearing on drive end for belted loads
- IP55 rating, enclosure protection against dust and water jets
- Suitable for use on a VFD. 10:1 variable torque and 10:1 constant torque
- 1.15 service factor on sinewave, 1.0 service factor on IGBT power
- Suitable for across the line, wye-delta, part winding, or inverter start
- 80°C rise at rated load
APPLICATIONS:
Specifically designed for the aggregate industry crusher applications such as
cone, jaw, and roller type impactors, pulverizers, etc. - Class F insulation
- Axial surface seal (50 to 200HP) and Inpro ® smart ring plus on the 250HP
model, rotating shaft seals on each end - External epoxy paint
- Brass drain and breather
- UL recognized, CSA certified, and CE mark
Category Product
Part# Summary
Quick Reference -
216-216 (19) Air Compressor -- Single Phase -- Dripproof -- (Rigid Base) (48)
Features:
- Capacitor start/capacitor run design for low amps and high
efficiency, as noted - High starting and breakdown torque
- Heavy gauge steel frame and base
- Continuous duty at nameplate ratings
- Thermal protection, as noted
- UL recognized and CSA certified
Category Product
Part# Summary
Quick Reference - Capacitor start/capacitor run design for low amps and high
-
217-217 (19) Air Compressor OEM Special Replacement -- Single Phase -- Dripproof -- (Rigid Base) (3)
Features:
- Capacitor start/capacitor run design for low amps and high efficiency
- Heavy gauge steel frame and base
- 1.0 service factor
- Manual thermal protection
- CW rotation facing opposites shaft end
Category Product
Part# Summary
Quick Reference -
217-217 (19) Cooling Tower -- Two-Speed-One Winding -- Variable Torque -- Blue Chip Series -- Severe Duty -- XRI -- Three Phase -- Totally Enclosed -- (Rigid Base) (13)
Applications:
Commercial and industrial fans, blowers, pumps, and other machinery that have variable torque characteristics. Prolonged use at low speed can result in significant energy savings.
Dripproof motors are intended for use in environments that are relatively clean and dry.
For use outdoors an enclosure or drip cover may be required (see accessories section).
Features:
- Ball Bearings
- 1.15 Service Factor
- UL Recognized and CSA Certified
Category Product
Part# Summary
Quick Reference -
218-218 (19) Multi-Speed: Two-Speed -- One-Winding -- Variable Torque -- Three Phase -- Dripproof -- (Rigid Base) (11)
Hydraulic Adaptor
Category Product
Part# Summary
Quick Reference -
218-218 (19) Multi-Speed: Two-Speed -- Two-Winding -- Variable Torque (31)
Applications:
Commercial and industrial fans, blowers, pumps, and other machinery that have variable torque characteristics. Prolonged use at low speed can result in significant energy savings.
Dripproof motors are intended for use in environments that are relatively clean and dry.
For use outdoors an enclosure or drip cover may be required (see accessories section).
Features:
- Ball Bearings
- 1.15 Service Factor
- UL Recognized and CSA Certified
- Economical two-winding design
Category Product
Part# Summary
Quick Reference -
219-219 (19) Instant Reversing -- Single Phase -- Capacitor Start -- (Dripproof) (11)
Features:
- Thermal protection, as noted
- Electronic instant reverse switch
- Extended clamp screws for mounting belt guard or accessories
- Three pole, double throw reversing switch supplied by customer
Category Product
Part# Summary
Quick Reference -
219-219 (19) Instant Reversing -- Single Phase -- Capacitor Start -- (TEFC) (1)
Features:
- Thermal protection, as noted
- Electronic instant reverse switch
- Extended clamp screws for mounting belt guard or accessories
- Three pole, double throw reversing switch supplied by customer
Category Product
Part# Summary
Quick Reference -
219-219 (19) Instant Reversing -- Single Phase -- Capacitor Start -- PSC -- (TENV) (1)
Features:
- Thermal protection, as noted
- Electronic instant reverse switch
- Extended clamp screws for mounting belt guard or accessories
- Three pole, double throw reversing switch supplied by customer Capacitor Start, Dripproof
Category Product
Part# Summary
Quick Reference -
220-220 (19) Kiln Duty -- XRI -- Blue Chip Series -- Severe Duty -- TEAO -- Three Phase -- (Rigid Base) (24)
Applications:
Fans found in kilns and other high ambient environments where long life and high efficiency are desired.
These TEAO motors must be mounted within the airstream for proper cooling.
Suitable for use on variable frequency drives.
Features:
- Blue Chip Series quality, 100% cast iron construction for rigidity and reduced vibration
- Internal and external epoxy paint
- CR 200 corona resistant magnet wire
- Class H insulation system
- Normally closed thermostats (one per phase, Class H)
- Heat stabilized ball bearings and high temperature grease
- Suitable for inverter use, 20:1 variable torque with 1.0 S.F . IN 90°C ambient
- Suitable for 90°C ambient at 1.15 S.F . or 100°C ambient at 1.0 S.F .
- Extended grease tubes, regreasable in service
- 8 foot leads
- UL recognized and CSA certified
Category Product
Part# Summary
Quick Reference -
221-221 (19) Oil Well Pump -- Three Phase -- Dripproof -- (Rigid Base) (15)
Applications:
For use on walking beam pumps found in oil field service.
Features:
- NEMA ® design D for extra high starting and breakdown torques
- Normally closed thermostats (one per phase, Class F)
- Fully guarded with screens on all external openings
- Copper bar rotor on 500 frame
- Low starting current with 5-8% slip
- Class F insulation
- F2 conduit box location
- Ball bearings (except as noted)
- Shaft slinger
- Special “oil well” duty
- 1.15 service factor
Category Product
Part# Summary
Quick Reference -
222-222 (19) Convection and Pizza Oven -- Split Phase -- (Single and Two Speeds) (8)
Features:
- Double sealed ball bearings
- Service factor as noted
- 60° C ambient
- Automatic reset overload protector
- ODP enclosure (except as noted)
Category Product
Part# Summary
Quick Reference -
223-223 (19) Pressure Washer -- Single Phase -- Dripproof -- (C-Face With Rigid Base) (8)
Features:
- Ball bearings, shaft end mechanically locked on C-face models
- Heavy gauge steel constructions
- Capacitor start/capacitor run design for higher efficiency (except as noted)
- Continuous duty, 1.15 service factor (except as noted)
- Thermal protection on some models
- UL recognized and CSA certified
Category Product
Part# Summary
Quick Reference -
223-223 (19) Pressure Washer -- Single Phase -- Dripproof -- (Rigid Base) (14)
Features:
- Ball bearings, shaft end mechanically locked on C-face models
- Heavy gauge steel constructions
- Capacitor start/capacitor run design for higher efficiency (except as noted)
- Continuous duty, 1.15 service factor (except as noted)
- Thermal protection on some models
- UL recognized and CSA certified
Category Product
Part# Summary
Quick Reference -
224-224 (19) Pressure Washer -- Single Phase -- Totally Enclosed Fan Cooled -- (C-Face With Rigid Base) (13)
Features:
- Ball bearings, shaft end mechanically locked on C-face models
- Heavy gauge steel constructions
- Capacitor start/capacitor run design for higher efficiency (except as noted)
- Continuous duty, 1.15 service factor
- Manual reset thermal protector
- UL recognized and CSA certified
Category Product
Part# Summary
Quick Reference -
224-224 (19) Pressure Washer -- Single Phase -- Totally Enclosed Fan Cooled -- (Rigid Base) (7)
Features:
- Ball bearings, shaft end mechanically locked on
C-face models - Heavy gauge steel constructions
- Capacitor start/capacitor run design for higher efficiency
(except as noted) - Continuous duty, 1.15 service factor
- Manual reset thermal protector
- UL recognized and CSA certified
Category Product
Part# Summary
Quick Reference - Ball bearings, shaft end mechanically locked on
-
225-225 (19) 50 Hertz -- Three Phase -- Dripproof -- (Rigid Base) (6)
Features:
- Ball bearings
- 1.15 Service Factor
- Nameplated 190-200-208/380-400-416 (except as noted)
- 12 Lead delta capability
- UL Recognized and CSA Certified
Category Product
Part# Summary
Quick Reference -
225-225 (19) Wood Working and Power Tool -- Single Phase -- Totally Enclosed -- (Rigid Base) (10)
Applications:
Replacement motors for table saws, planers, lathes, and other equipment found in the woodworking and metalworking trades.
These totally enclosed, fan cooled motors are
well suited for use in dusty and dirty environments or where wood or metal shavings are present.Features:
- Capacitor start design for high starting torque with low amps
- Double sealed ball bearings
- Heavy gauge steel frame and base
- 1.15 service factor
- Manual reset thermal protection
- Dependable, dust-proof centrifugal starting switch
- On/off toggle switch and 8 foot cord with 115 volt plug included on 1/2 to 1-1/2 HP models
- UL recognized and CSA certified
Category Product
Part# Summary
Quick Reference